Automotive 100-Mbps Ethernet CI Test Frequently Losing Packets While Gigabit Remains Stable? Root Cause + Solution Explained Clearly
简体中文
7days a week from 9:00 am to 9:0pm
+86 18016225001

Shanghai Leiditech上海雷卯电子科技有限公司是专业的静电保护元件厂家,TVS二极管供应商;专业提供防雷防静电方案,电磁兼容EMC免费测试等服务,品质保证,库存充足,型号齐全,值得信赖,如有采购静电保护元件,TVS二极管需求,请联系雷卯,24小时服务热线:021-50828806.

By LEIDITECH | 13 August 2026 | 0 Comments

Automotive 100-Mbps Ethernet CI Test Frequently Losing Packets While Gigabit Remains Stable? Root Ca

 

During vehicle-level EMC testing, perplexing issues often arise: with the same PCB and identical circuit architecture, 100BASE-T1 (100 Mbps Ethernet) experiences continuous dropouts and massive packet loss during CI coupling testing, while the 1000BASE-T1 (Gigabit Ethernet) port remains stable throughout with no anomalies.

Today, the Leiditech EMC engineer will break down the core root causes of this failure using real test cases, while also sharing a standardized protection solution that complies with IEEE and ISO automotive standards — one that hardware engineers can directly reuse.

I.Actual measurement fault phenomena and verification

1. Test comparison

· ✖ 100BASE-T1 (100 Mbps T1): Under CI coupled interference, communication frequently drops out, the console continuously displays "Request timed out," and Ping experiences severe packet loss.

· ✔ 1000BASE-T1 (Gigabit T1): Under the same interference environment, the link remains stable with no packet loss and no disconnection.

2.Fault recurrence

Fault recurrence: Packet loss can only be reproduced when a single unshielded twisted pair is coupled individually; no anomalies are observed when multiple wires are bundled together for testing.

Oscilloscope capture of the MDI differential waveform shows that CI RF interference severely distorts the differential signal, affecting data transmission.

3.Verification experiment

After removing the ESD protection components from the Ethernet port, the waveform distortion completely disappeared, and the packet loss and disconnection issues were fully resolved.

→ Root cause identified: The ordinary ESD devices were experiencing false triggering under RF interference.

II.Why does 100 Mbps lose packets while Gigabit is fine?

1.Root Cause

Ordinary low-trigger-voltage ESD devices have poor tolerance to RF interference. The continuous high-frequency noise coupled during CI testing, superimposed on the line voltage, can cause false reverse triggering of the ESD. Once triggered, it forcibly pulls the differential level low or high, destroying high-speed differential signal integrity and directly causing Ethernet communication packet loss.

2. Reasons why Gigabit ports remain unaffected by interference

1000BASE-T1 vehicle solutions mandatorily include shielded twisted pair (STP) + shielded connectors. The dual-layer shielding of the wiring harness and connector significantly blocks external RF noise from coupling into the differential signal lines, preventing false ESD triggering.

In contrast, traditional 100BASE-T1 solutions allow the use of unshielded twisted pair (UTP). Lacking shielding isolation, CI interference couples directly onto the differential lines, making it much easier to falsely trigger ordinary ESD devices.

III.Three major shortcomings of traditional solutions

 

Early NXP reference designs typically placed ESD protection behind the AC coupling capacitor (close to the PHY) and paired it with varistors for protection. However, this approach can no longer meet the stringent EMC requirements of modern automotive applications:

 

1. The long ESD and surge discharge path significantly degrades protection performance.

2. High-frequency CI/BCI interference coupled through the wiring harness has no pre-discharge path, leaving minimal system immunity margin.

3. Varistors have slow response times and poor clamping voltage accuracy, providing inadequate protection for high-speed signals.

 

IV.Leiditech Optimized Solution: Choose ≥100V High-Breakdown Dedicated Ethernet ESD

Industry hard standard requirements

IEEE automotive Ethernet standards mandate: Ethernet ESD devices must have a reverse breakdown voltage VBR ≥ 100V. This requirement fundamentally prevents false triggering caused by CI/BCI RF interference while meeting the ISO 10605:2023 ±25kV vehicle-level ESD test requirements.

 

Recommended automotive-grade dedicated ESD from Leiditech: PESD2ETH1GXT-QR

 

Core parameters adapted to automotive Ethernet scenarios:

Ÿ Reverse stand-off voltage 24V, perfectly matching automotive bus voltage.

Ÿ Minimum breakdown voltage 100V, eliminating false triggering caused by RF interference.

Ÿ I/O parasitic junction capacitance ≤ 1.2pF, ultra-low capacitance does not degrade high-speed eye diagrams.

Ÿ Clamping voltage as low as 32.5V under high current, reliably protecting the PHY chip from breakdown.

Ÿ SOT-23 standard package, pin-to-pin compatible with imported counterpart devices, no PCB redesign required.

Leiditech focuses on the R&D of automotive EMC protection solutions, offering a full range of automotive-grade ESD, TVS, and other components. We support domestic substitution and customized EMC rectification solutions, with extensive engineering implementation cases, stable and controllable delivery, and an in-house laboratory available for customers' free preliminary testing.

Leave a Reply

Your email address will not be published.Required fields are marked. *
Name
E-mail
Content
Verification code
ver_code