Analysis and countermeasures of lamp module failure caused by cost reduction of automobile generator
简体中文
7days a week from 9:00 am to 9:0pm
+86 18016225001

Shanghai Leiditech上海雷卯电子科技有限公司是专业的静电保护元件厂家,TVS二极管供应商;专业提供防雷防静电方案,电磁兼容EMC免费测试等服务,品质保证,库存充足,型号齐全,值得信赖,如有采购静电保护元件,TVS二极管需求,请联系雷卯,24小时服务热线:021-50828806.

By LEIDITECH | 12 February 2025 | 0 Comments

Analysis and countermeasures of lamp module failure caused by cost reduction of automobile generator


I. The cost reduction generator causes surge transactions

Recently, we encountered a case, a customer's car light module in the normal shipment process, a large number of modules suddenly appeared damaged. A detailed failure analysis report (8D report) is required.

 

In the process of customer communication, it was found that the end customer had replaced the car generator, and this change became the trigger of the problem. With the trend of automobile cost reduction, the load index of engine changes. The voltage output fluctuates sharply, and the frequency, peak voltage and current of the surge pulse jump sharply. Measured results show that the peak surge voltage generated by some reduced-cost generators can be increased several times compared with the traditional type, which poses a serious challenge to the lamp module.

 

The TVS (transient voltage suppression diode) in the headlight module was originally designed based on the traditional surge level. When facing the new high intensity surge, its rated protection ability is overwhelmed, and it is frequently broken down, resulting in the failure of the entire headlight module circuit.

二、Fault root analysis

The electronic components in the lamp module, such as the LED chip and the drive circuit, require high voltage and current stability. In the past, the protection devices based on the surge characteristics of traditional generators show fatigue in the surge environment caused by the new cost reduction. The protection threshold setting of these protective devices is difficult to match the surge amplitude after enhancement. When the strong surge pulse strikes, its clamping and discharge capacity is insufficient, the excessive voltage and current will directly impact the key electronic components, causing irreversible damage such as chip burning and circuit short circuit, seriously affecting the normal operation of the lamp module and greatly reducing its service life.

 

The block diagram of the lamp module is as follows, Lei MAO has the corresponding protection device for each interface, the customer's fault is the generator power supply to the LED driver module of the TVS protection device protection ability does not meet the new power caused by the replacement of high-power TVS devices to meet customer needs, the new cost borne by the end customer half.


三、Solutions and technical considerations

Leiditech electronic engineers through the self-built laboratory to help customers free of charge to find out the test, several years of valuable testing experience to design a series of automotive electronic protection devices and solutions. For example, for CAN bus electrostatic surge protection, Lei MAO Electronics uses low residual voltage TSS, the reaction time is ns level, which can prevent surge, but also anti-static, and ensure signal integrity. Meet ISO10605-2 (electrostatic contact discharge ±8kV, air discharge ±15KV), in line with the Beijing automotive enterprise standard BAS582-2019 for CAN bus BC contact discharge ±8KV, air discharge ±15KV requirements and surge requirements.

 

When customers choose electrostatic surge protection components (such as TVS), they can be selected according to the ISO 7637-25A /5B test standard or ISO 16750-2, and can also conduct prospective analysis and simulation tests on the possible future changes in the automotive electrical system, and choose a protection device with greater margin.


The recommended material numbers and parameters for the above solution are listed in the following table

四、Concept practice and industry outlook

Leiditech Electronics uphold the "duty, integrity, quality and win-win" concept, to help customers cope with the crisis, put forward the use of high surge absorption capacity of TVS upgrade program. Although the cost has increased, after honest communication and negotiation with the customer, we reached a consensus that only the customer should bear half of the cost increase. In the long run, if the surge protection vulnerability is not addressed, it may lead to large-scale aftermarket repairs and even product recalls, along with a sharp rise in repair, replacement, logistics costs, brand reputation damage and market share shrinkage. By implementing this program, customers can effectively solve the current product damage dilemma, restore market supply and confidence, and accumulate valuable technical solutions and practical experience for similar electrical changes in the future, ensure the quality stability and market competitiveness of the product throughout the life cycle, and harvest considerable long-term economic benefits.

 

This incident also highlights the importance of close communication with end customers. Any adjustment to the electrical architecture can have a profound impact on the headlight module. Therefore, in the initial stage of product design, it is very important to establish a sound information sharing mechanism and communication channels. Leimo Electronics will continue to be committed to providing customers with a full range of technical support and quality services to help your products stand out in the fierce market competition.

Conclusion

With the trend of cost reduction in the automotive industry, we have met new challenges through this case study. Through in-depth technical analysis and customized solutions, Lei MAO Electronics successfully helped customers solve the problem of lamp module failure. In the future, we will continue to be committed to providing customers with better EMC solutions to ensure the long-term stability and market competitiveness of our products.

 

Leiditech Electronics provides free consulting and sample verification services, and supports free EMC testing to help customers ensure that products meet safety standards!

 

Leiditech is committed to becoming a leading brand in the supply of electromagnetic compatibility solutions and components, supplying ESD, TVS, TSS, GDT, MOV, MOSFET, Zener, inductors and other products. Leiditech has an experienced R & D team, can provide personalized customized services according to customer needs, to provide customers with the best quality solutions.

Leave a Reply

Your email address will not be published.Required fields are marked. *
Name
E-mail
Content
Verification code
ver_code