PoE power supply methods and EMC protection in the DC power supply system of intelligent logistics robots
简体中文
7days a week from 9:00 am to 9:0pm
+86 18016225001

Shanghai Leiditech上海雷卯电子科技有限公司是专业的静电保护元件厂家,TVS二极管供应商;专业提供防雷防静电方案,电磁兼容EMC免费测试等服务,品质保证,库存充足,型号齐全,值得信赖,如有采购静电保护元件,TVS二极管需求,请联系雷卯,24小时服务热线:021-50828806.

By LEIDITECH | 16 November 2026 | 0 Comments

PoE power supply methods and EMC protection in the DC power supply system of intelligent logistics r

 

1. Introduction to intelligent logistics robots

With the deepening of supply chain digitalization and Industry 4.0, intelligent logistics robots—AGV (Automated Guided Vehicle) / AMR (Autonomous Mobile Robot)—have become the core driving force of intelligent logistics, evolving from simple "handling tools" into "mobile factories" with cognitive capabilities.

Since 2010, the DC power supply systems of intelligent logistics robots (AGV/AMR) have undergone a series of evolutions. It is not just that batteries have changed from lead-acid to lithium; the overall DC power system architecture has also evolved from a single, centralized link mainly based on direct battery voltage supply into a DC energy network graded by load scale: high-voltage or high-current energy storage layer → protected power bus → DC-DC point-of-load close to the load. For the vast majority of warehousing, handling, and lifting logistics robots, 48V is becoming the mainstream power bus that balances current, cabling, device ecosystem, and safety design.

The DC 48V power supply methods for internal units of the equipment are mainly divided into two categories: direct dedicated power line distribution, and power distribution methods that share lines with other signal lines (PoE – Power over Ethernet / PoDL – Power over Data-Lines / PoC – Power over Coaxial / etc.).

Currently, the internal unit power supply of mainstream intelligent logistics robots adopts a combination of direct dedicated power line distribution + PoE distribution.

2. PoE – Power over Ethernet power supply method

Power over Ethernet (PoE) is a technology that simultaneously transmits data and DC power over Ethernet twisted-pair cables. This technology has completely changed the cabling approach for network devices, making deployment more flexible, lower cost, and easier to manage centrally.

The core of PoE technology lies in the collaboration between PSE (Power Sourcing Equipment) and PD (Powered Device).

· PSE: Usually a PoE-capable switch or injector, responsible for injecting DC voltage into the network cable.

· PD: Such as IP cameras, VoIP phones, wireless APs, etc., which extract power from the network cable and operate normally.

· Communication process: Before formally supplying power, the PSE performs detection to confirm whether the other end is a PoE-compatible device, preventing damage from erroneous power supply.

PoE technology has undergone multiple standard upgrades, with current mainstream standards including:

· IEEE 802.3af (2003): The original standard, providing up to 15.4W of effective power, classified as Class 0-3.

· IEEE 802.3at (2009): Commonly known as PoE+, providing up to 30W of effective power, adding Class 4-5.

· IEEE 802.3bt (2018): Also known as PoE++ or 4PPoE, utilizing all four pairs for power supply, providing up to 90W of effective power, classified as Class 6-8.

Standard

Common Name

Wire Pairs

PSE-Side Power

PD-Side Actual

PSE Voltage Window

802.3af Type1

PoE

2 对2 pairs

15.4W

12.95W

44–57V

802.3at Type2

PoE+

2 对2 pairs

30W

25.5W

50–57V

802.3bt Type3

PoE++

4 对4 pairs

60W

51W

50–57V

802.3bt Type4

4PPoE

4 对4 pairs

90W

71.3W

50–57V

3. Intelligent logistics robot internal DC power supply architecture

Mainstream brand intelligent logistics robots internally adopt a two-stage power distribution of "battery power bus → 24V intermediate bus → point-of-load POL." The drive/motor is connected directly to the high-voltage bus; the rest is regulated by the main DC-DC to 24V (24V is a safety extra-low voltage widely adopted in industrial control), interfacing with safety PLCs/scanners/e-stops, and isolating battery fluctuations with SOC and voltage drops from motor start/stop.

 

PoE is a local data/short-distance power supply method. Its power is hard-constrained by standards, and it is only applicable to Ethernet PHY devices.

Using PoE: GigE Vision industrial cameras, onboard industrial PoE switches, vehicle-mounted wireless APs/backhaul, networked IO.

Not using PoE: Drive/steering wheel controllers, GPU industrial computers, BMS/chargers, safety PLCs and safety scanners (24V hardwired), navigation LiDAR.

4. ESD/EFT/Surge protection circuit design for DC power supply circuits

4.1 Standards and levels

Item

Standard default level

Industrial PoE switch product tightenedTightened by industrial PoE switch makers

ESD

EN 61000-6-2 default ±4kV contact / ±8kV air (Level 2)

Mainstream manufacturers tighten to ±8kV contact / ±15kV air

EFT

Power ±2kV / Signal ±1kV (Level 3)

Power/signal both ±4kV (Level 4)

Surge

Line-to-line ±1kV / Line-to-ground ±2kV (Level 3)

Line-to-line ±2kV / Line-to-ground ±4kV (Level 4)

Generic standards

EN 55032/55035; 61000-6-2 immunity / -6-4 emission

The complete device simultaneously meets -6-2/-6-4

 

±8kV contact / ±15kV air is IEC 61000-4-2 Level 4 (the most severe conventional level); Level 3 is ±6kV contact / ±8kV air. EN 61000-6-2 industrial environment defaults to referencing the Level 2 magnitude; ±8kV contact / ±15kV air is a proactive tightening by industrial switch manufacturers, not the standard definition of "industrial Level 3."

4.2 Non-PoE DC bus protection

Signal chain: reverse polarity protection → hot-swap/ORing controller → main TVS clamping → PPTC/fuse → bulk energy storage + π-type filtering (common-mode choke + X/Y capacitors) → DC-DC → load. For the 24V intermediate power bus TVS, Leiditech SMBJ26CA can be selected; for the 48V power bus, Leiditech SMBJ58CA can be selected.

 

4.3 PoE port protection

Multi-stage cascade: network transformer isolation → Bob-Smith common-mode absorption → ESD array low-capacitance clamping of differential lines → main power bus TVS protecting the 100V hot-swap MOSFET; for outdoor/long-run cabling, add a GDT+MOV at the frontmost stage and replace the main power bus clamping TVS with a higher surge-current version.

 

PoE port protection device location diagram: RJ45 → network transformer → Bob-Smith (75Ω+1000pF) → ESD array (Leiditech GBLC03C) → main bus TVS (Leiditech SMBJ58CA/LMBJ58CP4) → PD controller → isolated DC-DC → downstream.

 

PoE port protection device location solution (front-stage GDT+MOV, main clamping LMBJ58CP4, Ethernet port ESD GBLC03C)

5. PoE DC power supply advantages and disadvantages comparison

Dimension

PoE (Power over Ethernet)

Non-PoE hardwired DC-DC

Wiring

Single cable transmits data + power simultaneously; one RJ45 cable carries network + power

Power lines and signal lines are separated, requiring more connectors

Interoperability

IEEE 802.3af/at/bt auto-detection + classification, plug-and-play

No unified interface; custom voltage/reverse polarity protection

Power upper limit

Hard constraints: af 15.4W / at 30W / bt 60W / 90W; unusable for motors and GPU industrial computers

Limited only by bus capacity/wire gauge; can reach kW

Device type

Must be Ethernet PHY devices

Any DC load of any voltage can connect to the bus

ESD/Surge

Requires network transformer + Bob-Smith + ESD array; narrow TVS window, with SMBJ58CA as a typical solution

Only EFT/Surge line-to-line/line-to-ground, no magnetic component constraints

Cost

PD controller + isolated DC-DC + magnetic components result in high BOM; not economical for nodes <10W

Load switch/TVS + capacitors are sufficient; low BOM

Failure mode

PD/magnetic component failure = simultaneous loss of data + power; safety nodes require redundancy

Power lines and data lines are physically separated; a single point of failure does not cause data loss

AGV applicability

Suitable for internal sensing nodes: cameras, APs, edge boxes, IP sensors

Suitable for the main power bus and all non-Ethernet low-power rails

 

6. Summary and recommendations

Regarding the internal DC power supply system of intelligent logistics robots, the following recommendations are provided:

The power supply backbone remains unchanged: "battery bus → 24V intermediate bus → point-of-load POL," with the drive/motor connected directly to the high-voltage bus, and the safety loop independently at 24V. This is the industry's general design paradigm.

PoE positioning should be restrained: it should only serve data nodes such as cameras and vehicle-mounted APs, and should not be used as the main power supply design.

 

Safety scanners should not use PoE: SICK microScan3/nanoScan3 use 24V hardwired + independent Ethernet, and the safety loop must be independent and diagnosable.

Mature protection device solutions are available: for the 48V main bus TVS, use Leiditech SMBJ58CA/LMBJ58CP4; for the Ethernet port ESD array, use Leiditech GBLC03C; for Bob-Smith, use 75Ω+1000pF/2~3kV AC coupling; for non-PoE buses, use reverse polarity protection MOS + hot-swap + TVS with Leiditech SMBJ58CA/LMBJ58CP4.

Appendix: Leiditech protection solution component selection list

Interface

Typical Application

Brand

Recommended Model

Key Parameters

Package

PoE port / 48V bus (front-stage common mode)

Outdoor long-run frontmost stage, discharging large surge currents

Leiditech

3R090-5S

90V bidirectional, 1.5 pF, 5 kA (8/20 μs)

三极3-electrode (3-pole) Φ5.0 mm

PoE port / 48V bus (front-stage)

Cooperates with the front-stage gas discharge tube to block follow-on current

Leiditech

14D820KJ

Varistor voltage 82V, 6 kA (8/20 μs)

14D

24V intermediate bus

24V power bus differential-mode clamping

Leiditech

SMBJ26CA

Vrwm 26V, Vc 42.1V, 600W (10/1000 μs), bidirectional

SMB

48V main bus

48V bus differential-mode clamping

Leiditech

SMBJ58CA

Vrwm 58V, Vc 93.6V, 600W (10/1000 μs), bidirectional

SMB

48V main bus (PoE)

PoE 48V power supply dedicated main clamping

Leiditech

LMBJ58CP4

Vrwm 58V, Vc 60V, 3000W, bidirectional

SMB

Reverse polarity protection MOS gate

MOSFET gate-source clamping protection

Leiditech

BZT52C15S

15V, 200 mW

SOD-323

Ethernet port differential lines

Ethernet differential line ESD clamping, low junction capacitance

Leiditech

GBLC03C

Vrwm 3.3V, 0.6 pF, Ipp 20 A, bidirectional, ±30 kV

SOD-323

 

This article is compiled and published by the Leiditech EMC Engineer, focusing on EMC compliance and protection component selection for intelligent logistics robot products, and continuously sharing frontline engineering practices.

Need to develop a protection BOM for your intelligent logistics robot circuit? Contact the Leiditech EMC technical team for one-on-one selection support and compliance documentation templates.

#Shanghai Leiditech #LeiditechEMCEngineer #IntelligentLogisticsRobot #AGV #AMR #PoE #EMCProtection #TVSComponentSelection

 

Leave a Reply

Your email address will not be published.Required fields are marked. *
Name
E-mail
Content
Verification code
ver_code